Installation

Partitioning Unlike many other Linux distributions, Slackware does not make use of a graphical disk partitioning tool in its installer. Rather, Slackware makes use of fdisk(8) and cfdisk(8), both console tools. cfdisk is a curses-based partitioning tool while fdisk is not. Whichever you choose to use should only rarely matter. In this book, we'll only discuss fdisk. In order to partition your hard drive, you'll first need to know how to identify it. In Linux, all hardware is identified by a special file called a device file. These are all (typically) located in the /dev directory. If your hard drive is IDE, you will most likely find it as /dev/hda; however, many hard drives today including SATA disks are identified as SCSI devices by the kernel. If you don't know what your hard drive is identified in Linux as, fdisk can help you out. root@slackware:/# fdisk -l Disk /dev/sda: 72.7 GB, 72725037056 bytes 255 heads, 63 sectors/track, 8841 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Here, you can see that my system has a hard drive located at /dev/sda that is 72.7 GB in size. You can also see some additional info about this hard drive. (In my case, this is actually three SCSI hard drives on a hardware RAID controller that makes them appear as a single drive.) The -l argument to fdisk tells it to display the hard drives and all the partitions it finds on those drives, but won't make any changes to the disks. In order to actually partition our drives, we'll have to tell fdisk what drive to operate on. root@slackware:/# fdisk /dev/sda The number of cylinders for this disk is set to 8841. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): Now we've told fdisk what disk we wish to partition and it has dropped us into command mode after printing an annoying warning message. The 1024 cylinder limit has not been a problem for some time, and Slackware's boot loader will have no trouble booting disks larger than this. Typing m and hitting ENTER will print out a helpful message telling you what to do with fdisk. Command (m for help): m FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! FILL THIS IN! Now that we know what commands will do what, it's time to begin to partition our drive. At a minimum, you will need a single / partition and should create a swap partition. You might also want to make a seperate /home partition for storing user files (this will make it easier to upgrade later, or install a different Linux operating system by keeping all of your users' files on a seperate partition). So, let's go ahead and make three partitions. The command to create a new partition is n (which you would have noticed if you read the help). Command: (me for help): n Command action e extended p primary partition (1-4) p Partition number (1-4): 1 First cylinder (1-8841, default 1): 1 Last cylinder or +size or +sizeM or +sizeK (1-8841, default 8841): +8G Command (m for help): n Command action e extended p primary partition (1-4) p Partition number (1-4): 2 First cylinder (975-8841, default 975): 975 Last cylinder or +size or +sizeM or +sizeK (975-8841, default 8841): +1G Here we have created two partitions. The first is 8GB in size and the second is only 1GB. We can view our existing partitions with the p command. Command (m for help): p Disk /dev/sda: 72.7 GB, 72725037056 bytes 255 heads, 63 sectors/track, 8841 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 974 7823623+ 83 Linux /dev/sda2 975 1097 987997+ 83 Linux Both of these partitions are of type "83" which is the standard Linux filesystem. We will need to change /dev/sda2 to type "82" in order to make this a swap partition. We will do this with the t command. Command (m for help): t Partition number (1-4): 2 Hex code (type L to list codes): 82 Command (me for help): p Disk /dev/sda: 72.7 GB, 72725037056 bytes 255 heads, 63 sectors/track, 8841 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 974 7823623+ 83 Linux /dev/sda2 975 1097 987997+ 82 Linux swap The swap partition is a special partition that is used for virtual memory by the Linux kernel. If for some reason you run out of RAM, the kernel will move the contents of some of the RAM to swap in order to prevent a crash. The size of your swap partition is up to you. A great many people have participated have participated in a great many flamewars on the size of swap partitions, but a good rule of thumb is to make your swap partition about twice the size of your system's RAM. Since my machine has only 512MB of RAM, I decided to make my swap partition 1GB. You may wish to experiment with your swap partition's size and see what works best for you, but generally there is no harm in having "too much" swap. At this point we can stop, write these changes to the disk, and continue on, but I'm going to go ahead and make a third partition which will be mounted at /home. Command: (me for help): n Command action e extended p primary partition (1-4) p Partition number (1-4): 3 First cylinder (1098-8841, default 1098): 1098 Last cylinder or +size or +sizeM or +sizeK (1098-8841, default 8841): 8841 Now it's time to finish up and write these changes to disk. Command: (me for help): w The partition table has been altered! Calling ioctl() to re-read partition table. Synching disks. root@slackware:/# At this point, we are through partitioning our disks and are ready to begin the setup program. However, if you have created any extended partitions, you may wish to reboot once to ensure that they are properly read by the kernel.