diff options
| -rw-r--r-- | netconfig | 55 |
1 files changed, 44 insertions, 11 deletions
@@ -25,6 +25,7 @@ fi # /etc/rc.d/rc.inet1.conf # # This file contains the configuration settings for network interfaces. + # If USE_DHCP[interface] is set to "yes", this overrides any other settings. # If you don't have an interface, leave the settings null (""). @@ -35,44 +36,64 @@ fi # Several other parameters are available, the end of this file contains a # comprehensive set of examples. +# Important note for IPv6 stateless auto configuration (SLAAC) users: +# From Slackware 15.0 onwards, you need to set USE_SLAAC[0]="yes" (etc) below + # ============================================================================= -# Config information for eth0: +# IPv4 config information for eth0: IPADDR[0]="$RCIPCOPY" NETMASK[0]="$RCMASKCOPY" IPALIASES[0]="" USE_DHCP[0]="$USE_DHCP" DHCP_HOSTNAME[0]="$DHCP_HOSTNAME" -# Config information for eth1: +# IPv4 config information for eth1: IPADDR[1]="" NETMASK[1]="" IPALIASES[1]="" USE_DHCP[1]="" DHCP_HOSTNAME[1]="" -# Config information for eth2: +# IPv4 config information for eth2: IPADDR[2]="" NETMASK[2]="" IPALIASES[2]="" USE_DHCP[2]="" DHCP_HOSTNAME[2]="" -# Config information for eth3: +# IPv4 config information for eth3: IPADDR[3]="" NETMASK[3]="" IPALIASES[3]="" USE_DHCP[3]="" DHCP_HOSTNAME[3]="" -# Default gateway IP address: +# IPv4 default gateway IP address: GATEWAY="$GATEWAY" -# Change this to "yes" for debugging output to stdout. Unfortunately, -# /sbin/hotplug seems to disable stdout so you'll only see debugging output -# when rc.inet1 is called directly. +# ============================================================================= + +# IPv6 config information for eth0: +IP6ADDRS[0]="" +USE_SLAAC[0]="" +USE_DHCP6[0]="" + +# IPv6 config information for eth1: +IP6ADDRS[1]="" +USE_SLAAC[1]="" +USE_DHCP6[1]="" + +# IPv6 default gateway address: +GATEWAY6="" + +# ============================================================================= + +# Change this to "yes" for debugging output to stdout. DEBUG_ETH_UP="no" +# ============================================================================= + # Example of how to configure a bridge: # Note the added "BRNICS" variable which contains a space-separated list # of the physical or virtual network interfaces you want to add to the bridge. @@ -84,6 +105,8 @@ DEBUG_ETH_UP="no" #USE_DHCP[0]="" #DHCP_HOSTNAME[0]="" +# ============================================================================= + # Virtual interfaces to create - these are created before any address # configuration or bridge setup is done, so you may use these interfaces # as IFNAME or BRNICS values. These can be tun or tap interfaces: @@ -103,8 +126,10 @@ DEBUG_ETH_UP="no" #VIRTIFUSER[1]="someuser" #VIRTIFGROUP[1]="somegroup" -## Example config information for wlan0. Uncomment the lines you need and fill -## in your data. (You may not need all of these for your wireless network) +# ============================================================================= + +## Example config information for wlan0. Uncomment the lines you need and fill +## in your data. (You may not need all of these for your wireless network) #IFNAME[4]="wlan0" #IPADDR[4]="" #NETMASK[4]="" @@ -124,13 +149,15 @@ DEBUG_ETH_UP="no" #WLAN_WPADRIVER[4]="wext" #WLAN_WPAWAIT[4]=30 +# ============================================================================= + ## Some examples of additional network parameters that you can use. ## Config information for wlan0: #IFNAME[4]="wlan0" # Use a different interface name instead of # the default 'eth4' #IPALIASES[4]="192.168.5.10/24" # Set up an IP alias. A netmask may be given # with a /<prefix> after the IP address - if - # not supplied, /32 will be used as default. + # not supplied, /24 will be used as default. #HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address #MTU[4]="" # The default MTU is 1500, but you might need # 1360 when you use NAT'ed IPSec traffic. @@ -149,6 +176,11 @@ DEBUG_ETH_UP="no" # server is not found (ipv4ll link-local # adresses in the IP range 169.254.0.0/16 are # also known as "zeroconf" addresses) +#SLAAC_TIMEOUT[4]="15" # The default timeout for auto configuration to + # wait for the interface to come up is 15 sec. + # Increase the timeout if required. +#USE_RA[4]="yes" # Accept router advertisements even when SLAAC + # is disabled on the interface. #WLAN_ESSID[4]=DARKSTAR # An example of how you can override _any_ # parameter defined in rc.wireless.conf, by # prepending 'WLAN_' to the parameter's name. @@ -208,6 +240,7 @@ chmod 644 $ETCNETWORKS # For loopbacking. 127.0.0.1 localhost +::1 localhost $IPADDR $HOSTNM.$DOMAIN $HOSTNM # End of hosts. |