diff options
Diffstat (limited to 'rc.inet1')
| -rw-r--r-- | rc.inet1 | 50 |
1 files changed, 30 insertions, 20 deletions
@@ -62,8 +62,9 @@ for i in "${IFNAME[@]}"; do fi fi done -# Normally the ipv6 module would be automatically loaded when the first IP is assigned to an interface, -# but autoconf/accept_ra need to be set to 0 before that happens, so pre-load ipv6 here. +# Normally the ipv6 module would be automatically loaded when the first IP is assigned to an +# interface (assuming ipv6 has not been disabled entirely), but autoconf/accept_ra need to be +# set to 0 before that happens, so try to pre-load ipv6 here. if [ ! -e /proc/sys/net/ipv6 ]; then /sbin/modprobe ipv6 fi @@ -181,20 +182,26 @@ if_up() { if [ -x /etc/rc.d/rc.wireless ]; then . /etc/rc.d/rc.wireless ${1} start fi - # Disable v6 IP auto configuration before trying to bring up the interface: - echo "0" >/proc/sys/net/ipv6/conf/$1/autoconf - # Disable Router Advertisment for this interface until it's needed: - echo "0" >/proc/sys/net/ipv6/conf/$1/accept_ra - IF_UP=0 + if [ -e /proc/sys/net/ipv6 ]; then # ipv6 networking is available + # Disable v6 IP auto configuration before trying to bring up the interface: + echo "0" >/proc/sys/net/ipv6/conf/$1/autoconf + # Disable Router Advertisment for this interface until it's needed: + echo "0" >/proc/sys/net/ipv6/conf/$1/accept_ra + fi + local IF_UP=0 # Slackware historically favours dynamic configuration over fixed IP to configure interfaces, so keep that tradition: - if [ "${USE_DHCP[$i]}" = "yes" ] || [ "${USE_DHCP6[$i]}" = "yes" ]; then # use dhcpcd to bring interface up + if [ "${USE_DHCP[$i]}" = "yes" ] || { [ -e /proc/sys/net/ipv6 ] && [ "${USE_DHCP6[$i]}" = "yes" ]; }; then # use dhcpcd # Declare DHCP_OPTIONS array before adding new options to it: declare -a DHCP_OPTIONS=() # Set DHCP_OPTIONS for this interface: - if [ "${USE_DHCP[$i]}" = "yes" ] && [ "${USE_DHCP6[$i]}" != "yes" ]; then # only try v4 dhcp + if [ -e /proc/sys/net/ipv6 ]; then + if [ "${USE_DHCP[$i]}" = "yes" ] && [ "${USE_DHCP6[$i]}" != "yes" ]; then # only try v4 dhcp + DHCP_OPTIONS+=("-4") + elif [ "${USE_DHCP[$i]}" != "yes" ] && [ "${USE_DHCP6[$i]}" = "yes" ]; then # only try v6 dhcp + DHCP_OPTIONS+=("-6") + fi + else DHCP_OPTIONS+=("-4") - elif [ "${USE_DHCP[$i]}" != "yes" ] && [ "${USE_DHCP6[$i]}" = "yes" ]; then # only try v6 dhcp - DHCP_OPTIONS+=("-6") fi [ -n "${DHCP_HOSTNAME[$i]}" ] && DHCP_OPTIONS+=("-h" "${DHCP_HOSTNAME[$i]}") [ "${DHCP_KEEPRESOLV[$i]}" = "yes" ] && DHCP_OPTIONS+=("-C" "resolv.conf") @@ -216,7 +223,7 @@ if_up() { /sbin/ip link set dev ${1} down fi fi - if [ "${USE_DHCP6[$i]}" != "yes" ] && [ "${USE_SLAAC[$i]}" = "yes" ]; then # configure interface via stateless auto config + if [ -e /proc/sys/net/ipv6 ] && [ "${USE_DHCP6[$i]}" != "yes" ] && [ "${USE_SLAAC[$i]}" = "yes" ]; then # configure via SLAAC echo "/etc/rc.d/rc.inet1: using Router Advertisement stateless auto configuration for ${1}" | $LOGGER # Enable accepting of router advertisment packets, and auto configuration of interfaces: echo "1" >/proc/sys/net/ipv6/conf/$1/accept_ra @@ -236,11 +243,6 @@ if_up() { fi fi if [ "${USE_DHCP[$i]}" != "yes" ] && [ -n "${IPADDR[$i]}" ]; then # add a fixed v4 IP to the interface - # IPv6's Duplicate Address Detection (DAD) causes a race condition when bringing up interfaces, as - # described here: https://www.agwa.name/blog/post/beware_the_ipv6_dad_race_condition - # Disable DAD while bringing up the interface - but note that this means the loss of detection of a - # duplicate address. It's a trade off, unfortunately. - echo "0" >/proc/sys/net/ipv6/conf/$1/accept_dad if [ -z "${NETMASK[$i]}" ]; then echo "/etc/rc.d/rc.inet1: no NETMASK set for ${1} - assuming 24 (aka, 255.255.255.0)" | $LOGGER NETMASK[$i]="24" @@ -255,7 +257,13 @@ if_up() { /sbin/ip link set dev ${1} down fi fi - if [ "${USE_DHCP6[$i]}" != "yes" ] && [ "${USE_SLAAC[$i]}" != "yes" ] && [ -n "${IP6ADDR[$i]}" ]; then # add a fixed v6 IP + if [ -e /proc/sys/net/ipv6 ] && [ "${USE_DHCP6[$i]}" != "yes" ] && [ "${USE_SLAAC[$i]}" != "yes" ] && \ + [ -n "${IP6ADDR[$i]}" ]; then # add a fixed v6 IP + # IPv6's Duplicate Address Detection (DAD) causes a race condition when bringing up interfaces, as + # described here: https://www.agwa.name/blog/post/beware_the_ipv6_dad_race_condition + # Disable DAD while bringing up the interface - but note that this means the loss of detection of a + # duplicate address. It's a trade off, unfortunately. + echo "0" >/proc/sys/net/ipv6/conf/$1/accept_dad if [ -z "${PREFIXLEN[$i]}" ]; then echo "/etc/rc.d/rc.inet1: no PREFIXLEN set for ${1} - assuming 64" | $LOGGER PREFIXLEN[$i]="64" @@ -288,7 +296,7 @@ if_up() { fi done fi - if [ -n "${IP6ALIASES[$i]}" ]; then + if [ -e /proc/sys/net/ipv6 ] && [ -n "${IP6ALIASES[$i]}" ]; then # IPv6's Duplicate Address Detection (DAD) causes a race condition when bringing up interfaces, as # described here: https://www.agwa.name/blog/post/beware_the_ipv6_dad_race_condition # Disable DAD while bringing up the interface - but note that this means the loss of detection of a @@ -315,7 +323,9 @@ if_up() { /sbin/ip link set dev ${1} promisc on fi # Reset accept_dad back to default now all the IPs are configured: - cat /proc/sys/net/ipv6/conf/default/accept_dad >/proc/sys/net/ipv6/conf/$1/accept_dad + if [ -e /proc/sys/net/ipv6 ]; then + cat /proc/sys/net/ipv6/conf/default/accept_dad >/proc/sys/net/ipv6/conf/$1/accept_dad + fi fi else debug_log "${1} is already up, skipping" |