summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Quiet down the ipv6 modprobe. Tell the user what is going on.Darren 'Tadgy' Austin2019-11-151-1/+3
| | | | Thanks to upnort for the suggestions.
* Fix up 'ipv6' modprobe config to match othersRobby Workman2019-11-151-0/+6
|
* Fix up 'bonding' modprobe config to match othersRobby Workman2019-11-151-0/+7
|
* README.bonding: Fix minor typosRobby Workman2019-11-141-3/+3
|
* README.VLANs: Fix minor typosRobby Workman2019-11-141-2/+2
|
* README.IPv6: Fix minor typos and grammar stuffRobby Workman2019-11-141-7/+7
|
* Remove toplevel README - it's stale now.Robby Workman2019-11-141-26/+0
|
* Update text in rc.inet1.conf, and sync with netconfig.Darren 'Tadgy' Austin2019-11-142-32/+70
|
* Update documentation. Default BONDMODE to balance-rr. Update rc.inet1.conf.Darren 'Tadgy' Austin2019-11-144-16/+238
|
* Several small fixes - see log.Darren 'Tadgy' Austin2019-11-131-8/+24
| | | | | | | | | * Added more debug_log calls around taking down interfaces. * When taking down a bridge, put the member interfaces down too. * Configure wireless interfaces before everything else - it might be that a wireless interface is part of a bond/bridge/VLAN. * When taking down VLAN interfaces, check if the underlying interface has an IP address. If it does, leave it up; else take it down.
* When creating a bond, flush the underlying interface IP.Darren 'Tadgy' Austin2019-11-131-4/+2
| | | | Also removed redundant setting of a 0.0.0.0 IP address.
* Remove BONDOPTS, VLANOPTS and BROPTS and replace with generic IFOPTS.Darren 'Tadgy' Austin2019-11-132-29/+45
| | | | | | | | | | Previously we had an xOPTS variable for each type of interface that could be configured. I've replaced this with a generic IFOPTS option which can be used to supply interface type specific options to 'ip'. As the option is now generic, it can be applied to physical interfaces too; so interfaces such as eth0 can have options applied just like a virtual interface.
* In rc.inet1.conf, be consistant with spacing and commenting.Darren 'Tadgy' Austin2019-11-131-46/+45
|
* Added support for a BROPTS variable to set bridge specific settings.Darren 'Tadgy' Austin2019-11-132-7/+18
| | | | | | | Before, it was not possible to set bridge specific options when creating a bridge. This option adds the ability to set options via a BROPTS variable, which takes a pipe (|) delimited set of options as documented in the ip-link(8) man page (search for "BRIDGE Type Support").
* Be consistent with variable case. Emit warning when assuming netmask.Darren 'Tadgy' Austin2019-11-131-47/+50
|
* Create and document a new VLANOPTS variable.Darren 'Tadgy' Austin2019-11-132-0/+12
| | | | | This variable can be used to set custom options to configure the VLAN interface. It does not need to be used in 'normal' operation with a VLAN.
* Initial support for bonding (link aggrigation) in rc.inet1.Darren 'Tadgy' Austin2019-11-133-7/+72
| | | | | | | | | | | | | | | | | | | The bonding code introduces three new variables for use in rc.inet1.conf: BONDNICS[x]="" BONDMODE[x]="" BONDOPTS[x]="" The BONDNICS variable takes a list of interfaces which should be slaved to the bond. BONDMODE sets the mode of the bond. Useful options are 'balance-rr', 'active-backup' and '802.3ad'. A full list of options can be found in /usr/src/linux/Documentation/networking/bonding.txt and README.bonding. BONDOPTS are a pipe (|) separated list of options to apply to the bond after the interfaces have been added. Useful options are 'primary' (which is required when BONDMODE is 'active-backup', 'xmit_hash_policy' (which can be used with 'balance-rr' to choose the hash policy, 'lacp_rate' (which should be used with '802.3ad' mode), and 'miimon' (which should be used with all modes) See the kernel source documentation or README.bonding for more info.
* Small fixes - see full log.Darren 'Tadgy' Austin2019-11-122-13/+10
| | | | | | | | | | | Remove code to skip interfaces that do not have IP addresses configured. This checking is redundant now, and prevents interfaces being brought up without IP addresses - which is important for bridging/bonding/VLANs. When grabbing the vlan ID from the interface name, use ## instead of #. Move the point where bridges are taken down to before the point where wireless interfaces are taken down. This is required so that a bridge on a wireless interface is take down before the interface itself. When looping through the interfaces to take down, use MAXNICS-1.
* Add example ipv6.conf for the modprobe.d directory.Darren 'Tadgy' Austin2019-11-121-0/+2
|
* Fix typo when de-configuring interfaces, i->1.Darren 'Tadgy' Austin2019-11-111-1/+1
|
* VLAN support. Sync logging/IPv6 changes from tadgy-ipv6-fixes branch.Darren 'Tadgy' Austin2019-11-112-73/+132
| | | | | | | | | | | | | | | | | | | | rc.inet1: * VLAN support added to rc.inet1{,.conf}. * Created new info_log function to replace $LOGGING variable. * When logging to syslog, use a tag of 'rc.inet1' with PID. * Decrease script noisyness at non-debug levels. * Add more debugging logging for testing. * Use -4 when configuring IPv4 loopback address. * Configure ::1 for IPv6 loopbacking. * Use 'local' not 'declare' in functions. * Move where DAD is disabled when setting IPv6 addresses. * Add error checking to some calls to 'ip'. * Walk backwards through interfaces when deconfiguring. rc.wireless: * Log to syslog, failling back to stdout. * Output error to stderr if not called from rc.inet1. Manpages and netconfig: * Updated for new VLAN support.
* Update rc.inet1.conf in netconfig. Update manpage.Darren 'Tadgy' Austin2019-11-072-0/+41
|
* Added README.VLANs with some basic usage instructions.Darren 'Tadgy' Austin2019-11-071-0/+20
|
* Walk _backwards_ through interfaces when deconfiguring.Darren 'Tadgy' Austin2019-11-071-2/+3
|
* Document MAXNICS in rc.inet1.conf. Extended VLAN description.Darren 'Tadgy' Austin2019-11-071-1/+7
|
* Initial commit of VLAN support.Darren 'Tadgy' Austin2019-11-072-4/+45
|
* Update manpages for changes to rc.inet1Darren 'Tadgy' Austin2019-11-061-26/+11
|
* Update rc.inet1.conf in netconfig.Darren 'Tadgy' Austin2019-11-061-14/+17
|
* Put IPv6 config with the IPv4 config in rc.inet1.confDarren 'Tadgy' Austin2019-11-061-14/+17
|
* Use 'broadcast +' for bringing up interfaces in IPALIASES block.Darren 'Tadgy' Austin2019-11-061-2/+2
|
* Remove IP6ALIASES block. IP6ADDR->IP6ADDRS.Darren 'Tadgy' Austin2019-11-061-17/+1
|
* Sync netconfig's rc.inet1.conf with the new one. Add ::1 to loopback in hostsDarren 'Tadgy' Austin2019-11-061-11/+44
|
* New configuration methodology - see full commit log.Darren 'Tadgy' Austin2019-11-062-24/+24
| | | | | | | | | | | It occurred to me that IPv6 addresses don't really need to have IP6ALIASES since all IPs are just added to the interface itself. So I've changed the syntax from using IP6ADDR + PREFIXLEN + IP6ALIASES to using just a single IP6ADDRS array, which takes a list of IP addresses with a prefix length in a space separated list. eg: IP6ADDRS[0]="a:b:c:d::1/64 1:2:3::1/48" If the prefix length is omitted a /64 length is assumed and a warning emitted.
* Updated specification and wrapped all lines at 80 chars.Darren 'Tadgy' Austin2019-11-061-128/+191
|
* If modprobe events occurred, sleep for a bit after they finishedRobby Workman2018-11-261-1/+6
| | | | | | This is ugly, but it beats doing the sleep regardless of whether there's any need for it and causing folks to whine about two seconds of loss in boot time.
* Add README.IPv6Darren 'Tadgy' Austin2018-11-262-9/+183
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* Updated manpagesDarren 'Tadgy' Austin2018-11-262-124/+208
| | | | | | Thanks to David Spencer for much of this. Signed-off-by: Robby Workman <rworkman@slackware.com>
* Flush ip addresses on lo when taking interfaces downDarren 'Tadgy' Austin2018-11-261-0/+2
| | | | | | | This prevents an annoying "RTNETLINK answers: File exists" warning when restarting networking Signed-off-by: Robby Workman <rworkman@slackware.com>
* Enable RA for DHCP/Fixed IP if explicitly told to do soDarren 'Tadgy' Austin2018-11-261-0/+8
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* In if_down(), only perform IPv6 operations if IPv6 is activeDarren 'Tadgy' Austin2018-11-261-4/+8
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* Remove hard coded -L from dhcpcd command lineDarren 'Tadgy' Austin2018-11-261-4/+2
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* Added USE_RA[x] option to explicitly enable/disable RA supportDarren 'Tadgy' Austin2018-11-262-3/+14
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* Protect blocks of code by testing whether ipv6 is activeDarren 'Tadgy' Austin2018-11-251-20/+30
| | | | | | | | | | This has the effect of allowing someone to disable ipv6 entirely, and the script do the right thing. Move the enabling of DAD into the correct section - no idea how it ended up in the ipv4 block of code. D'oh. Signed-off-by: Robby Workman <rworkman@slackware.com>
* Various fixups for nomenclature - see full commit messageDarren 'Tadgy' Austin2018-11-252-33/+54
| | | | | | | | | | | | | | | | * USE_AUTOCONF->USE_SLAAC to be more consistent with IPv6 terminology * PREFIX6->PREFIXLEN to be more consistent with IPv6 terminology Thanks to David Spencer (idlemoor) for the patch to the above * AUTOCONF_TIMEOUT->SLAAC_TIMEOUT to be consistent with USE_SLAAC change Since some options for IPv6 no longer end in '6', we can relax the naming of others, so these make sense: IPADDR6->IP6ADDR ; IPALIASES6->IP6ALIASES Update to rc.inet1.conf example file - thanks to David Spencer. Signed-off-by: Robby Workman <rworkman@slackware.com>
* Move interface module loading into a 'pre-load' sectionDarren 'Tadgy' Austin2018-11-251-9/+21
| | | | | | | | | Also fix loading of interface modules - previously just $i was used, where it should have been ${i%%:*} Also added pre-loading of ipv6 module Signed-off-by: Robby Workman <rworkman@slackware.com>
* Mitigate a race condition with Duplicate Address DetectionDarren 'Tadgy' Austin2018-11-251-4/+12
| | | | | | | | | | https://www.agwa.name/blog/post/beware_the_ipv6_dad_race_condition This removes the need to sleep for 3 seconds after setting up the interfaces, but does mean we lose detection of address clashes on the inteface - it's a trade off Signed-off-by: Robby Workman <rworkman@slackware.com>
* rc.inet1: sleep for 3 seconds after setting all the interface options/IPsDarren 'Tadgy' Austin2018-11-251-0/+4
| | | | | | | | | | | In testing here, this was necessary to prevent daemons reporting 'Cannot assign requested address' for IPv6 addresses when they attempt to bind() to the interface address. This only seems to affect v6 addresses - v4 addresses seem to be immediately available to bind() - but a 3 second pause shouldn't hurt given that the other methods of configuration can block for up to 15 seconds. Signed-off-by: Robby Workman <rworkman@slackware.com>
* Update rc.inet1.conf with IPv6 optionsDarren 'Tadgy' Austin2018-11-251-1/+14
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* Added ipv6 gateway up/down functionDarren 'Tadgy' Austin2018-11-251-4/+15
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* Added support for AUTOCONF6_TIMEOUT[x] optionDarren 'Tadgy' Austin2018-11-251-4/+5
| | | | | | Removed unneeded sleep when taking interface down Signed-off-by: Robby Workman <rworkman@slackware.com>
generated by cgit v1.2.3 (git 2.26.2) at 2024-11-22 23:06:13 +0000