summaryrefslogtreecommitdiffstats
path: root/rc.inet1.conf
Commit message (Collapse)AuthorAgeFilesLines
* Remove BONDOPTS, VLANOPTS and BROPTS and replace with generic IFOPTS.Darren 'Tadgy' Austin2019-11-131-14/+19
| | | | | | | | | | Previously we had an xOPTS variable for each type of interface that could be configured. I've replaced this with a generic IFOPTS option which can be used to supply interface type specific options to 'ip'. As the option is now generic, it can be applied to physical interfaces too; so interfaces such as eth0 can have options applied just like a virtual interface.
* In rc.inet1.conf, be consistant with spacing and commenting.Darren 'Tadgy' Austin2019-11-131-46/+45
|
* Added support for a BROPTS variable to set bridge specific settings.Darren 'Tadgy' Austin2019-11-131-7/+12
| | | | | | | Before, it was not possible to set bridge specific options when creating a bridge. This option adds the ability to set options via a BROPTS variable, which takes a pipe (|) delimited set of options as documented in the ip-link(8) man page (search for "BRIDGE Type Support").
* Create and document a new VLANOPTS variable.Darren 'Tadgy' Austin2019-11-131-0/+6
| | | | | This variable can be used to set custom options to configure the VLAN interface. It does not need to be used in 'normal' operation with a VLAN.
* Initial support for bonding (link aggrigation) in rc.inet1.Darren 'Tadgy' Austin2019-11-131-0/+17
| | | | | | | | | | | | | | | | | | | The bonding code introduces three new variables for use in rc.inet1.conf: BONDNICS[x]="" BONDMODE[x]="" BONDOPTS[x]="" The BONDNICS variable takes a list of interfaces which should be slaved to the bond. BONDMODE sets the mode of the bond. Useful options are 'balance-rr', 'active-backup' and '802.3ad'. A full list of options can be found in /usr/src/linux/Documentation/networking/bonding.txt and README.bonding. BONDOPTS are a pipe (|) separated list of options to apply to the bond after the interfaces have been added. Useful options are 'primary' (which is required when BONDMODE is 'active-backup', 'xmit_hash_policy' (which can be used with 'balance-rr' to choose the hash policy, 'lacp_rate' (which should be used with '802.3ad' mode), and 'miimon' (which should be used with all modes) See the kernel source documentation or README.bonding for more info.
* Document MAXNICS in rc.inet1.conf. Extended VLAN description.Darren 'Tadgy' Austin2019-11-071-1/+7
|
* Initial commit of VLAN support.Darren 'Tadgy' Austin2019-11-071-0/+14
|
* Put IPv6 config with the IPv4 config in rc.inet1.confDarren 'Tadgy' Austin2019-11-061-14/+17
|
* New configuration methodology - see full commit log.Darren 'Tadgy' Austin2019-11-061-6/+2
| | | | | | | | | | | It occurred to me that IPv6 addresses don't really need to have IP6ALIASES since all IPs are just added to the interface itself. So I've changed the syntax from using IP6ADDR + PREFIXLEN + IP6ALIASES to using just a single IP6ADDRS array, which takes a list of IP addresses with a prefix length in a space separated list. eg: IP6ADDRS[0]="a:b:c:d::1/64 1:2:3::1/48" If the prefix length is omitted a /64 length is assumed and a warning emitted.
* Added USE_RA[x] option to explicitly enable/disable RA supportDarren 'Tadgy' Austin2018-11-261-0/+2
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* Various fixups for nomenclature - see full commit messageDarren 'Tadgy' Austin2018-11-251-19/+40
| | | | | | | | | | | | | | | | * USE_AUTOCONF->USE_SLAAC to be more consistent with IPv6 terminology * PREFIX6->PREFIXLEN to be more consistent with IPv6 terminology Thanks to David Spencer (idlemoor) for the patch to the above * AUTOCONF_TIMEOUT->SLAAC_TIMEOUT to be consistent with USE_SLAAC change Since some options for IPv6 no longer end in '6', we can relax the naming of others, so these make sense: IPADDR6->IP6ADDR ; IPALIASES6->IP6ALIASES Update to rc.inet1.conf example file - thanks to David Spencer. Signed-off-by: Robby Workman <rworkman@slackware.com>
* Update rc.inet1.conf with IPv6 optionsDarren 'Tadgy' Austin2018-11-251-1/+14
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* Fix up setting of IPALIASES and update docscurrent-20180531Darren Austin2018-05-241-1/+3
| | | | Signed-off-by: Robby Workman <rworkman@slackware.com>
* rc.inet1*: Allow setting an interface in promiscuous modeDarren Austin2018-05-241-0/+1
| | | | | | | This is needed for container networking - the bridge for it must be in promiscuous mode. Signed-off-by: Robby Workman <rworkman@slackware.com>
* rc.inet1*: Simplify virtif_* code, add note to example configJakub Jankowski2017-11-211-1/+3
| | | | | | | | | | | | | There is a built-in way of counting the number of elements in an array: ${#arrayname[@]}. Use this, and the fact that "for i in $(seq 0 -1)" will not evaluate body of the loop even once, to simplify code and get rid of virtif_determine(). While at it, add a note to rc.inet1.conf mentioning the necessity of keeping array indexes monotonically increasing (from 0), otherwise the code will fail (so would the original code). Signed-off-by: Robby Workman <rworkman@slackware.com>
* rc.inet1*: Fix DHCP timeoutcurrent-20171121Robby Workman2017-11-211-1/+1
| | | | | This was accidentally changed from 15 seconds back to the 14.2 default of 10 seconds. Thanks to Eduard Rozenberg.
* rc.inet1.conf: Clarify comment wrt bridge interfacesRobby Workman2017-10-071-1/+1
|
* rc.inet1.*: Added support for IP address aliasesRobby Workman2017-07-141-0/+5
| | | | | | | | | | | | | This is accomplished with a new parameter in rc.inet1.conf: IPALIASES[$index]="space separated list of addresses" The aliases are added with a /32 mask and a label of ${interface}:{$number} to remain compatible with net-tools. IP address aliases are supported for both statically configured interfaces and dhcp-configured interfaces, although they'll only be configured for dhcp if the dhcpcd call succeeds. * note: I don't what happens if dhcpcd gets IPv4LL address
* rc.inet1{,.conf}: Allow create/destroy of virtual tun/tap devicesRobby Workman2017-07-121-0/+17
|
* Initial commit of rc.inet1* and rc.wireless*Robby Workman2017-01-061-0/+117
If other files are needed, they can be added later
generated by cgit v1.2.3 (git 2.26.2) at 2024-11-01 07:19:59 +0000