# /etc/rc.d/rc.inet1.conf # # This file contains the configuration settings for network interfaces. # If USE_DHCP[interface] is set to "yes", this overrides any other settings. # If you don't have an interface, leave the settings null (""). # You can configure network interfaces other than eth0,eth1... by setting # IFNAME[interface] to the interface's name. If IFNAME[interface] is unset # or empty, it is assumed you're configuring eth. # Several other parameters are available, the end of this file contains a # comprehensive set of examples. # Important note for IPv6 stateless auto configuration (SLAAC) users: # From Slackware 15.0 onwards, you need to set USE_SLAAC[0]="yes" (etc) below # ============================================================================= # IPv4 config information for eth0: IPADDR[0]="" NETMASK[0]="" IPALIASES[0]="" USE_DHCP[0]="" DHCP_HOSTNAME[0]="" # IPv6 config information for eth0: IP6ADDRS[0]="" USE_SLAAC[0]="" USE_DHCP6[0]="" # IPv4 config information for eth1: IPADDR[1]="" NETMASK[1]="" IPALIASES[1]="" USE_DHCP[1]="" DHCP_HOSTNAME[1]="" # IPv6 config information for eth1: IP6ADDRS[1]="" USE_SLAAC[1]="" USE_DHCP6[1]="" # IPv4 config information for eth2: IPADDR[2]="" NETMASK[2]="" IPALIASES[2]="" USE_DHCP[2]="" DHCP_HOSTNAME[2]="" # IPv6 config information for eth2: IP6ADDRS[2]="" USE_SLAAC[2]="" USE_DHCP6[2]="" # IPv4 config information for eth3: IPADDR[3]="" NETMASK[3]="" IPALIASES[3]="" USE_DHCP[3]="" DHCP_HOSTNAME[3]="" # IPv6 config information for eth3: IP6ADDRS[3]="" USE_SLAAC[3]="" USE_DHCP6[3]="" # IPv4 default gateway IP address: GATEWAY="" # IPv6 default gateway IP address: GATEWAY6="" # ============================================================================= # Change this to "yes" for debugging output to stdout. DEBUG_ETH_UP="no" # MAXNICS is the maximum number of interfaces that will be configured. # You may need to increase the MAXNICS value if you have many interfaces, or # you use multiple VLANs and/or bridges. The default is 6. # MAXNICS="6" # ============================================================================= # Example of how to configure a bond (link aggrigation) interface. # IFNAME[0]="bond0" # BONDNICS[0]="eth0 eth1" # BONDMODE[0]="balance-rr" # BONDOPTS[0]="xmit_hash_policy layer2+3 | miimon 100" # IPADDR[0]="192.168.0.1" # NETMASK[0]="24" # IPALIASES[0]="" # USE_DHCP[0]="" # DHCP_HOSTNAME[0]="" # IP6ADDRS[0]="" # USE_SLAAC[0]="" # USE_DHCP6[0]="" # ============================================================================= # Example of how to configure a VLAN interface. # The VLAN ID is taken from the full interface name, which is comprised of the # underlying interface name, a period (.) and then the VLAN ID. # IFNAME[0]="eth0.10" # IPADDR[0]="192.168.10.1" # NETMASK[0]="24" # IPALIASES[0]="" # USE_DHCP[0]="" # DHCP_HOSTNAME[0]="" # IP6ADDRS[0]="" # USE_SLAAC[0]="" # USE_DHCP6[0]="" # ============================================================================= # Example of how to configure a bridge: # Note the added "BRNICS" variable which contains a space-separated list # of the physical or virtual network interfaces you want to add to the bridge. #IFNAME[0]="br0" #BRNICS[0]="eth0" #IPADDR[0]="192.168.0.1" #NETMASK[0]="255.255.255.0" #IPALIASES[0]="" #USE_DHCP[0]="" #DHCP_HOSTNAME[0]="" # ============================================================================= # Virtual interfaces to create - these are created before any address # configuration or bridge setup is done, so you may use these interfaces # as IFNAME or BRNICS values. These can be tun or tap interfaces: # adjust VIRTIFNAME and VIRTIFTYPE accordingly. # Starting with VIRTIFNAME[0] is mandatory, and each next one must be # incremented by one, so VIRTIFNAME[1], VIRTIFNAME[2], and so on. # # Virtual tap interface example #VIRTIFNAME[0]="tap0" #VIRTIFTYPE[0]="tap" #VIRTIFUSER[0]="root" #VIRTIFGROUP[0]="root" # # Virtual tun interface example #VIRTIFNAME[1]="tun0" #VIRTIFTYPE[1]="tun" #VIRTIFUSER[1]="someuser" #VIRTIFGROUP[1]="somegroup" # ============================================================================= ## Example config information for wlan0. Uncomment the lines you need and fill ## in your data. (You may not need all of these for your wireless network) #IFNAME[4]="wlan0" #IPADDR[4]="" #NETMASK[4]="" #USE_DHCP[4]="yes" #DHCP_HOSTNAME[4]="icculus-wireless" #DHCP_KEEPRESOLV[4]="yes" #DHCP_KEEPNTP[4]="yes" #DHCP_KEEPGW[4]="yes" #DHCP_IPADDR[4]="" #WLAN_ESSID[4]=DARKSTAR #WLAN_MODE[4]=Managed #WLAN_RATE[4]="54M auto" #WLAN_CHANNEL[4]="auto" #WLAN_KEY[4]="D5A31F54ACF0487C2D0B1C10D2" #WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=96389dc66eaf7e6efd5b5523ae43c7925ff4df2f8b7099495192d44a774fda16" #WLAN_WPA[4]="wpa_supplicant" #WLAN_WPADRIVER[4]="wext" #WLAN_WPAWAIT[4]=30 # ============================================================================= ## Some examples of additional network parameters that you can use. ## Config information for wlan0: #IFNAME[4]="wlan0" # Use a different interface name instead of # the default 'eth4' #IPALIASES[4]="192.168.5.10/24" # Set up an IP alias. A netmask may be given # with a / after the IP address - if # not supplied, /24 will be used as default. #HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address #MTU[4]="" # The default MTU is 1500, but you might need # 1360 when you use NAT'ed IPSec traffic. #PROMISCUOUS[4]="yes" # Set promiscuous mode on the interface. #DHCP_TIMEOUT[4]=15 # The default timeout for the DHCP client to # wait for server resonse is 15 seconds, but # you might want a shorter or longer wait. #DHCP_KEEPRESOLV[4]="yes" # If you don't want /etc/resolv.conf overwritten #DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten #DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change # your default gateway #DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP # server #DHCP_DEBUG[4]="yes" # Make dhcpcd show verbose diagnostics #DHCP_NOIPV4LL[4]="yes" # Do not assign an ipv4ll address when a DHCP # server is not found (ipv4ll link-local # adresses in the IP range 169.254.0.0/16 are # also known as "zeroconf" addresses) #SLAAC_TIMEOUT[4]="15" # The default timeout for auto configuration to # wait for the interface to come up is 15 sec. # Increase the timeout if required. #USE_RA[4]="yes" # Accept router advertisements even when SLAAC # is disabled on the interface. #WLAN_ESSID[4]=DARKSTAR # An example of how you can override _any_ # parameter defined in rc.wireless.conf, by # prepending 'WLAN_' to the parameter's name. # Useful with multiple wireless interfaces. #WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey" # Some drivers require a private ioctl to be # set through the iwpriv command. If more than # one is required, you can place them in the # IWPRIV parameter (separated with the pipe (|) # character, see the example). #WLAN_WPA[4]="wpa_supplicant" # Run wpa_supplicant for WPA support #WLAN_WPADRIVER[4]="ndiswrapper"# Tell wpa_supplicant to specifically use the # ndiswrapper driver (if you leave this empty # the 'wext' driver is used by default) #WLAN_WPAWAIT[4]=30 # In case it takes long for the WPA association # to finish, you can increase the wait time # (defaults to 10 seconds)