Initial commit of rc.inet1* and rc.wireless*

If other files are needed, they can be added later

1 files changed, 225 insertions, 0 deletions

diff --git a/rc.wireless.conf b/rc.wireless.conf
new file mode 100644
index 0000000..d02d7c2
--- /dev/null
+++ b/rc.wireless.conf
@@ -0,0 +1,225 @@
+# Wireless LAN adapter configuration
+#
+# Theory of operation : 
+#
+# The script attempts to match a block of settings to the specific wireless
+# card inserted, the *first* block matching the card is used.
+# The address format is "hwaddr", with * as a wildcard.
+# 'hwaddr' is the unique MAC address identifier of the wireless card.
+# The MAC address is usually printed on the card, or can be found via ifconfig.
+# Some examples here use only half of the MAC address with a wildcard to
+# match a whole family of cards...
+#
+# All the Wireless specific configuration is done through the Wireless
+# Extensions, so we will just call 'iwconfig' with the right parameters
+# defined below.
+# Of course, you need to have iwconfig installled on your system.
+# To download iwconfig, or for more info on Wireless Extensions :
+#	http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html
+#
+# Note : you don't need to fill all parameters, leave them blank, in most
+# cases the driver will initialise itself with sane defaults values or
+# automatically figure out the value... And no drivers do support all
+# possible settings...
+#
+# -- This is a modified '/etc/pcmcia/wireless.opts' script --
+# -- I added sections for Prism/GT and Atheros based cards --
+# --    (supported by the prism54 and madwifi drivers)     --
+# --              16/sep/2004 * Eric Hameleers             --
+#
+
+VERBOSE=1
+
+case "$HWADDR" in
+
+## NOTE : Comment out the following five lines to activate the samples below ...
+## --------- START SECTION TO REMOVE -----------
+## Pick up any Access Point, should work on most 802.11 cards
+*)
+    INFO="Any ESSID"
+    ESSID="any"
+    ;;
+## ---------- END SECTION TO REMOVE ------------
+
+
+# Here are a few examples with a few Wireless LANs supported...
+# The matching is done on the first 3 bytes of the MAC address
+
+# SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter 
+00:04:E2:*)
+    INFO="SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter"
+    # ESSID (extended network name) : My Network, any
+    ESSID="any"
+    # NWID/Domain (cell identifier) : 89AB, 100, off
+    NWID=""
+    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
+    MODE="Managed"
+    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
+    FREQ=""
+    CHANNEL="7"
+    # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
+    SENS=""
+    # Bit rate : auto, 1M, 11M,54M
+    RATE="auto"
+    # Encryption key : 4567-89AB-CD, s:password
+    # Example for 40-bit encryption:
+    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
+    # Example for 104-bit encryption (aka 128-bit WEP):
+    #KEY="d5ad2f05abd048ecf10b1c80c7"
+    KEY=""
+    # RTS threshold : off, 500
+    RTS=""
+    # Fragmentation threshold : off, 1000
+    FRAG=""
+    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
+    IWCONFIG=""
+    # iwspy parameters : + 01:23:45:67:89:AB
+    IWSPY=""
+    # iwpriv parameters : set_port 2, set_histo 50 60
+    IWPRIV=""
+;;
+
+# Multiband Atheros based 802.11a/b/g universal NIC cards
+00:05:4E:*)
+    INFO="Multiband Atheros based 802.11a/b/g universal NIC"
+    # ESSID (extended network name) : My Network, any
+    ESSID=""
+    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
+    MODE="Managed"
+    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
+    FREQ=""
+    CHANNEL="7"
+    # Bit rate : auto, 1M, 11M,54M
+    RATE="auto"
+    # Encryption key : 4567-89AB-CD, s:password
+    # Example for 40-bit encryption:
+    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
+    # Example for 104-bit encryption (aka 128-bit WEP):
+    #KEY="d5ad2f05abd048ecf10b1c80c7"
+    KEY=""
+    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
+    IWCONFIG=""
+    # iwspy parameters : + 01:23:45:67:89:AB
+    IWSPY=""
+    # iwpriv parameters : set_port 2, set_histo 50 60
+    IWPRIV=""
+    ;;
+
+# Lucent Wavelan IEEE (+ Orinoco, RoamAbout and ELSA)
+# Note : wvlan_cs driver only, and version 1.0.4+ for encryption support
+00:60:1D:*|00:02:2D:*)
+    INFO="Wavelan IEEE example (Lucent default settings)"
+    ESSID="Wavelan Network"
+    MODE="Managed"
+    #RATE="auto"
+    KEY="s:secu1"
+    # To set all four keys, use :
+    #KEY="s:secu1 [1] key s:secu2 [2] key s:secu3 [3] key s:secu4 [4] key [1]"
+    # For the RG 1000 Residential Gateway: The ESSID is the identifier on
+    # the unit, and the default key is the last 5 digits of the same.
+    #ESSID="084d70"
+    #KEY="s:84d70"
+    ;;
+
+# Cisco/Aironet 4800/3x0
+# Note : MPL driver only (airo/airo_cs), version 1.3 or later
+00:40:96:*|00:02:8A:*)
+    INFO="Cisco/Aironet example (Cisco default settings)"
+    ESSID="any"
+    # To set all four ESSID, use iwconfig v21 and the same trick as above
+    MODE="Managed"
+    #RATE="11M auto"
+    #KEY="d5ad2f05abd048ecf10b1c80c7"
+    KEY="off"
+    ;;
+
+# Samsung MagicLan (+ some other PrismII cards)
+# Note : Samsung binary library driver, version 1.20 or later
+00:00:F0:*|00:02:78:*)
+    INFO="Samsung MagicLan example (Samsung default settings)"
+    ESSID="any"
+    MODE="Managed"
+    CHANNEL="4"
+    RATE="auto"
+    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
+    #IWCONFIG="power on"
+    ;;
+
+# Raytheon Raylink/WebGear Aviator2.4
+# Note : doesn't work yet, please use for debugging only :-(
+00:00:8F:*|00:00:F1:*)
+    INFO="Raylink/Aviator2.4 example (Aviator default ad-hoc setting)"
+    ESSID="ADHOC_ESSID"
+    MODE="Ad-Hoc"
+    RATE="auto"
+    IWPRIV="set_framing 1"
+    ;;
+
+# Old Lucent Wavelan
+08:00:0E:*)
+    INFO="Wavelan example (Lucent default settings)"
+    NWID="0100"
+    MODE="Ad-Hoc"
+    FREQ="2.425G"
+    KEY="off"
+    ;;
+
+# Netwave (Xircom Netwave/Netwave Airsurfer)
+00:80:C7:*)
+    INFO="Netwave example (Netwave default settings)"
+    NWID="100"
+    KEY="00"
+    ;;
+
+# Proxim RangeLan2/Symphony (what is the MAC address ???)
+XX:XX:XX:*)
+    INFO="Proxim RangeLan2/Symphony example"
+    NWID="0"
+    MODE="Master"
+    CHANNEL="15"
+    IWPRIV="setsubchan 1"
+    ;;
+
+# No Wires Needed Swallow 550 and 1100 setting (what is the MAC address ???)
+XX:XX:XX:*)
+    INFO="NWN Swallow example"
+    ESSID="session"
+    KEY="0000-0000-00 open"
+    ;;
+
+# Symbol Spectrum24 setting (what is the MAC address ???)
+XX:XX:XX:*)
+    INFO="Symbol Spectrum24 example"
+    ESSID="Essid string"
+    ;;
+
+# Generic example (decribe all possible settings)
+*)
+    INFO="Fill with your own settings..."
+    # ESSID (extended network name) : My Network, any
+    ESSID=""
+    # NWID/Domain (cell identifier) : 89AB, 100, off
+    NWID=""
+    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
+    MODE=""
+    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
+    FREQ=""
+    CHANNEL=""
+    # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
+    SENS=""
+    # Bit rate : auto, 1M, 11M
+    RATE=""
+    # Encryption key : 4567-89AB-CD, s:password
+    KEY=""
+    # RTS threshold : off, 500
+    RTS=""
+    # Fragmentation threshold : off, 1000
+    FRAG=""
+    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
+    IWCONFIG=""
+    # iwspy parameters : + 01:23:45:67:89:AB
+    IWSPY=""
+    # iwpriv parameters : set_port 2, set_histo 50 60
+    IWPRIV=""
+    ;;
+esac